vod205t, vod206t, VOD207T, vod211t, vod213t, www.vishay.com vishay semiconductors rev. 1.2, 23-nov-12 1 document number: 81956 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototransistor output, dual channel, soic-8 package description the vod205t, vod206t, VOD207T, vod211t, vod213t, vod217t are optically coupled pairs with a gallium arsenide infrared led and a silicon npn phototransistor. signal information, including a dc level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. features ? two channel coupler ? soic-8 surface mountable package ? standard lead spacing of 0.05" ? available only on ta pe and reel option (conforms to eia standard 481-2) ? isolation test voltage, 4000 v rms ? compatible with dual wave, vapor phase and ir reflow soldering ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 agency approvals ? ul1577, file no. e52744 system code y ? cul - file no. e52744, equivalent to csa bulletin 5a ? din en 60747-5-5 (vde 0884-5) approved, contact customer service if this option is required notes (1) i f = 10 ma (2) i f = 1 ma i179018-1 a1 c2 a3 c4 8c 7e 6c 5e v de i179074 ordering information vod2 # # t part number agency certified/package ctr (%) ul, cul 40 to 80 63 to 125 100 to 200 > 20 > 100 (1) > 100 (2) soic-8 vod205t vod206t VOD207T vod211t vod213t vod217t absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input peak reverse voltage v r 6v peak pulsed current 1 s, 300 pps i fm 1a continuous forward current per channel i f 30 ma power dissipation p diss 50 mw derate linearly from 25 c 0.66 mw/c output collector emitter breakdown voltage bv ceo 70 v emitter collector breakdown voltage bv eco 7v continuous output current i cmax. 50 ma power dissipation per channel p diss 125 mw derate linearly from 25 c 1.67 mw/c s ioc-8 6.1 mm
vod205t, vod206t, VOD207T, vod211t, vod213t, www.vishay.com vishay semiconductors rev. 1.2, 23-nov-12 2 document number: 81956 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mounted devices. fig. 1 - power dissipation vs. ambient temperature note ? minimum and maximum values were tested requierements. typical va lues are characteristics of the device and are the result of e ngineering evaluations. typical values are for information only and are not part of the testing requirements. coupler isolation test voltage t = 1 s v iso 4000 v rms total package dissipation ambient (2 leds and 2 detectors, 2 channels) p tot 300 mw derate linearly from 25 c 4mw/c storage temperature t stg - 40 to + 150 c operating temperature t amb - 40 to + 100 c soldering time from 260 c (1) t sld 10 s absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit iild205t_07 200 150 100 50 0 t a - ambient temperature (c) package power dissipation (mw) 25 50 75 100 125 total pkg per channel electrical characteristcs (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input forward voltage i f = 10 ma v f 1.2 1.55 v reverse current v r = 6 v i r 0.1 100 a capacitance v r = 0 v c o 25 pf output collector emitter breakdown voltage i c = 100 a bv ceo 70 v emitter collector breakdown voltage i e = 100 a bv eco 7v collector emitter leakage current v ce = 10 v, i f = 0 a i ceo 550na collector emitter capacitance v ce = 0 v c ce 10 pf collector emitter sa turation voltage i f = 10 ma, i c = 2.5 ma v cesat 0.4 v coupler capacitance (input to output) c io 0.5 pf
vod205t, vod206t, VOD207T, vod211t, vod213t, www.vishay.com vishay semiconductors rev. 1.2, 23-nov-12 3 document number: 81956 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 2 - switching test circuit current transfer ratio parameter test condition part symbol min. typ. max. unit i c /i f v ce = 5 v, i f = 10 ma vod205t ctr dc 40 80 % vod206t ctr dc 63 125 % VOD207T ctr dc 100 200 % vod211t ctr dc 20 % vod213t ctr dc 100 % v ce = 5 v, i f = 1 ma vod205t ctr dc 13 30 % vod206t ctr dc 22 45 % VOD207T ctr dc 34 70 % vod217t ctr dc 100 120 % switching characteristics parameter test condition symbol min. typ. max. unit turn-on time i c = 2 ma, r l = 100 , v cc = 5 v t on 5s turn-off time i c = 2 ma, r l = 100 , v cc = 5 v t off 4s rise time i c = 2 ma, r l = 100 , v cc = 5 v t r 5s fall time i c = 2 ma, r l = 100 , v cc = 5 v t f 4s common mode transient immunity parameter test condition symbol min. typ. max. unit common mode transient immunity at logic high v cm = 1000 v p-p , r l = 1 k , i f = 0 ma |c mh | 10 000 v/s common mode transient immunity at logic low v cm = 1000 v p-p , r l = 1 k , i f = 10 ma |c ml | 10 000 v/s iil215at_17 v cc = 5 v input v out r l t fall 10 % 50 % 90 % t off t on t rise output input 10 % 50 % 90 % v 0 0
vod205t, vod206t, VOD207T, vod211t, vod213t, www.vishay.com vishay semiconductors rev. 1.2, 23-nov-12 4 document number: 81956 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 3 - test circuit for common mode transient immunity note ? as per iec 60747-5-5, 7.4.3.8.2, this optoco upler is suitable fo r safe electrical in sulation only within the safety ratings . compliance with the safety ratings shall be ensured by means of protective circuits. r f v b = 4.5 v 1, 2, 4 3 b a 6 5 r l 1 k v o 5 v dc 0.1 f v cm input from hv pulse source + - 21628 dt dt dv = 63 % of v cm dv = 63 % of v cm common mode voltage v cm 2.0 v 2.0 v v o v o cm h cm l 0.8 v 0.8 v time 21626 safety and insulation ratings parameter test condition symbol min. typ. max. unit climatic classifica tion according to ie c 68 part 1 40/100/21 polution degree 2 comparative tracking index cti 175 399 peak transient overvoltage v iotm 6000 v peak insulation voltage v iorm 560 v resistance (input to output) r io 100 g apparent charge method a q pd c apparent charge method b q pd c safety rating - power output p so 350 mw safety rating - input current i si 150 ma safety rating - temperature t si 165 c external creepage distance 4 mm internal creepage distance 4 mm external clearance distance 4 mm insulation thickness 0.2 mm
vod205t, vod206t, VOD207T, vod211t, vod213t, www.vishay.com vishay semiconductors rev. 1.2, 23-nov-12 5 document number: 81956 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 4 - forward current vs. forward voltage fig. 5 - collector emitter current vs. v ce fig. 6 - normalized ctr ce vs. forward current fig. 7 - current transfer ratio (normalized) vs. ambient temperature fig. 8 - switching speed vs. load resistor fig. 9 - collector current vs. ambient temperature 30 25 85 c 60 c 25 c 20 10 5 0 15 0.6 1.0 0.8 1.2 1.4 iild205t_01 v f - led forward voltage (v) i f - led current (ma) iild205t_02 0 6 10 12 1.2 1.0 0.8 0.6 0.4 0.2 0.0 v ce - collector to emitter voltage (v) nic normalized collector current i f = 10 ma i f = 5 ma i f = 1 ma coll current normalized at i = 10 ma f v ce = 10 v 4 2 8 iild205t_03 nctr ce - normalized ctr ce 0.01 0.1 1 10 100 1.2 1.0 0.8 0.6 0.4 0.2 0.0 i f - led current (ma) v ce = 5 v ctr normalized at i f = 10 ma v ce = 0.4 v iild205t_04 20 40 60 80 100 1.2 1.0 0.8 0.6 0.4 0.2 0.0 t a - temperature (c) nctr ce - normalized ctr ce i f = 5 ma i f = 1 ma i f = 10 ma ctr nonsat normalized at i f = 10 ma v ce = 10 v iild205t_05 switching speed (s) 0.1 1 10 100 10 3 10 2 10 1 10 0 r l - load resistor (k ) i f = 10 ma pulse width = 100 ms duty cycle = 50 % t off t on 0.001 0.01 i ceo - leakage current (a) 0.1 1 20 60 100 80 40 t a - temperature (c) iild205t_06 v ce = 50 v v ce = 10 v
vod205t, vod206t, VOD207T, vod211t, vod213t, www.vishay.com vishay semiconductors rev. 1.2, 23-nov-12 6 document number: 81956 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example of VOD207T) tape and reel packaging dimensions in millimeters fig. 10 - tape and reel shipping medium (eia-481, revision a, an d iec 60286), 2000 units per reel fig. 11 - tape dimens ions, 2000 parts per reel 0.91 0.36 4.32 1.14 6.6 r 0.13 1.27 i178020 iso method a 40 6.10 1.27 typ. 0.41 0.1 0.2 lead coplanarity 0.001 max. 0.20 7 3.05 0.05 c l r 0.25 max. 1.02 5 max. pin one id 3.91 0.05 0.38 0.05 5.84 0.05 0.51 0.10 2 plcs. 1.49 0.05 3.18 0.05 d207 v yww y 68 esd sticker tape slot in core 330 (13") regular, special or bar code label 17999 18004-1 1.5 1.75 0.1 13.3 0.3 max. 0.1 max. 16.0 0.3 4 0.1 2 0.05 6.6 6.35 8.0 7.5 0.05 3.8 embossment direction of feed center lines of cavity 10 pitch cumulative tolerance on tape 0.2 1.5 min. pin 1 and top of component top cover tape
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
